Picture two glasses of the same drink at room temperature, each with a thermometer in it. One gets bullet ice and the other gets nugget ice. Which thermometer drops faster?
This article measures only that: how many degrees the drink loses per minute. It doesn't cover how cold the ice feels in your hand, how long it lasts, or how much it waters down the drink. It answers one question, how fast the drink's temperature falls.
The short answer in degrees per minute
Compare equal grams of ice at the same starting temperature. On that basis, nugget ice should drop the drink's temperature faster in the first few minutes. Nugget ice is made of compacted flakes with air pockets between them, so each gram has much more surface touching the drink, and that surface keeps breaking open to expose fresh cold ice.
The lead is modest, and three things can erase or even reverse it:
- Scoops instead of grams. Nugget ice is airy and bullet pieces are dense, so a scoop of bullet ice can hold noticeably more ice.
- Bullet ice's hollow center. The inside wall also touches the drink, so a bullet piece has more surface than its smooth outside suggests.
- Stirring. Moving the liquid speeds up heat transfer enough to matter more than the shape of the ice.
We should be clear about the evidence. We found no controlled, published head-to-head measurement of bullet ice versus nugget ice in a drink. This answer comes from heat-transfer principles. Further down, you'll find a five-minute thermometer test to check it in your own kitchen.
Where the cooling rate comes from
Heat transfer at a surface follows a simple relationship, set out in the DOE handbook chapter on convection heat transfer:
Q̇ = h × A × ΔT
Q̇ is the rate of heat flow. A is the surface area of ice touching the drink. ΔT is the temperature difference between the drink and the ice surface. h is a coefficient that depends on how the liquid moves past that surface. Shape mostly affects A. Stirring affects h. The drink's starting temperature affects ΔT.
Melting does most of the work
Melting one gram of ice at 0 °C absorbs about 334 J. Water's specific heat is about 4.186 J per gram per degree, and as HyperPhysics notes, that relationship doesn't apply during a phase change. While ice melts, its temperature stays put and the energy goes into the melting. For each gram, melting absorbs roughly twice the energy needed to warm that same gram of liquid water by 40 °C (about 167 J), or about 80 times the energy needed to warm it by 1 °C.
So melting isn't a side effect of cooling. It's the main way the ice pulls heat out of the drink.
The meltwater film is the bottleneck
The moment ice touches a warm drink, a thin layer of meltwater forms on its surface. This layer sits near 0 °C, and every bit of heat has to cross it to reach the ice.
Ice conducts heat roughly four times better than liquid water (about 2.22 vs 0.54 W/m·K). That means the slow step isn't inside the ice. It's on the water side, through the film and the still liquid next to it. Anything that thins or breaks up that layer speeds up cooling.
Stirring does exactly that. A stirred glass with the "slower" shape can beat an unstirred glass with the "faster" one. If you stir one glass and not the other, you're comparing stirring, not shapes.
Smaller pieces of the same mass melt faster
Split a fixed mass of ice into smaller pieces and you expose more surface per gram. A classroom demonstration in the Journal of Chemical Education shows this with ice cubes versus a block. More area means more heat flow per second, and that means a faster temperature drop.
Why nugget ice gives up its cold faster

Nugget ice is made by compressing thin ice flakes into small, porous pieces with trapped air. That structure helps it on all three levers:
- More boundary per gram. Each nugget is a cluster of flake surfaces, not one solid lump, so A is large for its mass.
- Fresh surfaces keep appearing. As the flakes melt and come loose, new ice at about 0 °C is exposed to the drink. Meltwater can drain through the porous body instead of building up into one thick, insulating film on a smooth face.
- Irregular packing. Nuggets don't form a single smooth wall against the liquid, so more of the drink touches ice directly.
This all points to a faster drop in degrees per minute, especially at the start. It doesn't tell you how long the ice lasts or how much it dilutes the drink. Those are different questions with different answers.
The case for bullet ice: it isn't a solid cylinder
Bullet ice gets dismissed as "smooth and solid," but that's only half right. Each piece is hollow, and as our comparison of bullet ice and other shapes points out, that hollow center increases the surface exposed to the drink. Liquid flows into the tube, so the inner wall cools the drink along with the outer wall.
Bullet ice also packs a lot of ice into each piece. Its walls are dense, with no trapped air, so a scoop of bullet ice usually weighs more than the same scoop of nuggets. That's where the answer can flip:
- If you weigh the ice, nugget ice should win on degrees per minute per gram.
- If you scoop the ice, the bullet glass may simply have more grams of ice in it. More ice means more total surface area, and the bullet glass can match or beat the nugget glass in the first minute.
Most people scoop, so many kitchen comparisons are really comparing different amounts of ice.
Speed isn't the same as capacity
Equal grams of ice at the same temperature hold the same amount of cold. Shape changes how fast that cold reaches the drink, not how much there is.
Here's some quick arithmetic. It's a calculation, not a measurement:
- Cooling a 250 g drink from 22 °C to 5 °C takes about 250 × 17 × 4.18 ≈ 17.8 kJ.
- Melting 60 g of ice at 0 °C absorbs about 60 × 334 ≈ 20 kJ from melting alone, plus about 1.3 kJ more as that meltwater warms to 5 °C.
For a single glass, the total amount of cold usually isn't the limit. The speed of heat transfer is, and that's where shape matters.
To turn heat flow into degrees per minute: 250 g of drink takes about 1,045 J to change by 1 °C. If 40 W were flowing into the ice (2,400 J per minute), the drink would drop about 2.3 °C per minute. At 120 W, it would drop about 6.9 °C per minute. These wattages are illustrative assumptions, not measured values for either shape. They show that anything that raises the heat flow, such as more area, a thinner film, or a bigger temperature gap, translates directly into degrees per minute.
How starting temperature changes the answer
The drink's starting temperature
The drink's temperature sets ΔT. A warm drink against ice at about 0 °C has a large gap, so heat moves quickly. As the drink cools, the gap shrinks and every shape slows down.
So nugget ice's lead in degrees per minute is largest early on and in warmer drinks. In a drink that's already cool, both shapes are working against a small gap, and the difference between them shrinks.
The ice's starting temperature
Ice that's colder than 0 °C can absorb some extra heat before it starts to melt. Take ice from a freezer running around −18 °C as an example. Ice's specific heat is about 2.05 J per gram per degree, so warming it from −18 °C to 0 °C absorbs about 18 × 2.05 ≈ 37 J per gram. That's roughly 11% of the 334 J that melting absorbs.
Once the surface is wet and melting, it stays near 0 °C no matter how cold the core is. That means colder ice adds more to total capacity than to the cooling rate. Comparing nuggets from a freezer with bullets at 0 °C fresh from the machine's basket still skews the result, though, so match the ice temperatures before you compare.
A five-minute test you can run

You need a kitchen scale, an instant-read thermometer, and two identical glasses.
- Match the drinks. Pour the same mass of the same drink into each glass, for example 250 g, and let both reach the same temperature.
- Match the ice. Weigh equal masses of each shape, for example 60 g. Take both from the same place so they start at the same temperature.
- Add both at once. Drop the ice into both glasses at the same moment and start a timer.
- Stir the same way. Either don't stir either glass, or give each one the same few slow stirs before every reading.
- Read every 30 seconds for five minutes. Record the drink temperature, keeping the probe at the same depth and away from the ice.
- Compute the rate. Divide the temperature drop in the first two minutes by two to get °C per minute for each glass.
What to expect: at equal mass, the nugget glass should fall faster at first, and the gap between the glasses should narrow as both approach their final temperature.
What would surprise you, and why: if the bullet glass wins at equal mass, check the stirring, the ice temperatures, and whether the hollow centers filled with liquid. Then run the test again with a scoop of each instead of weighing. That shows how much of the everyday difference comes from the amount of ice rather than its shape.
Choosing a shape, and the machine that makes it
Start by deciding which shape you want, then check that the machine actually makes it.
- For the fastest per-minute drop in a glass, gram for gram, choose nugget ice. You'll find nugget models in our nugget ice maker collection.
- For dense pieces with a lot of ice per scoop, choose bullet ice. Our bullet ice maker collection shows the options.
Our Euhomy Pearl L1 Nugget Ice Maker produces soft, chewable nugget ice in 7–10 minutes.
Our Euhomy Dart H1 Silver Bullet Ice Maker takes 6 minutes to make 9 bullet-shaped ice cubes.
When you compare spec sheets, remember that "7–10 minutes" and "6 minutes" describe how quickly a machine makes ice, not how quickly that ice cools a drink. Those numbers tell you how soon you can refill a glass. They don't predict the degrees per minute in it.
If you want the rest of the comparison, including texture, flavor, and how each shape holds up, see our guide to nugget ice vs. bullet ice.
The decision rule
- Weighing the ice, same temperatures, no stirring: expect nugget ice to win the first minutes in °C per minute.
- Scooping: bullet ice may win simply because the scoop holds more grams of ice.
- Stirring: stir both glasses, or the stirring will decide the result more than the shape.
- Warm drink: the gap between shapes is largest here. In an already cool drink, it hardly matters.
If you're not sure which applies in your kitchen, run the five-minute test with a scale and a thermometer and compare the numbers.